How To Reset GM Instrument Cluster? Step by Step (2023)

To reset a GM Instrument Cluster, typically you need to:

  1. Turn off the vehicle.
  2. Remove the key from the ignition.
  3. Disconnect the vehicle’s battery for a few minutes.
  4. Reconnect the battery and start the vehicle to see if the cluster has been reset.

How to Reset GM Instrument Cluster?

If you ever notice flickering gauges or inaccurate readings on your vehicle, then driving that car can be hard for you. The reason behind these problems is the bad instrument cluster. So if you want to run the car properly, you should know How To Reset GM Instrument Cluster.

You can drive the GM without it, but it will not be safe enough for your car. Moreover, there will be no information regarding the speed, heat, fuel, or distance, so you will have no idea about the low fuel and check engine situation.

But if you want to get the new ones, the expense will only cost you a lot of money. So if you reset it, then it will save you a lot of money. But how can you reset the GM instrument cluster? In this article, you can find a step-by-step process for resetting the GM instrument cluster. So after reading this article to the end, we hope you will not get disappointed!

Step by Step: How to Reset GM Instrument Cluster?

How to Reset GM Instrument Cluster 1 1

Step 1: Removing Headlight Fuses

At first, you have to go through the headlight. Then, after that, you have to turn the headlight on and then off. That’s it.

You must do this thing again and again at the start. Continuously turning the light off and on might affect the HID headlights. As a result, the lifetime of your HID headlights will obviously boost!

Previously, you have to check the fuse box. Fuse boxes are usually situated under the hood. From the fuse box, you have to separate the 15A right and left low headlight fuses.

Check positions 1 and 6. However, we always recommend you check the owner’s manual.

You should always check the owner’s manual and then choose which positions you need to check out. And after that, complete this step.

Note: In this circumstance, you have to ensure that you are reinstalling the headlight fused with the low beam. So, kindly re-check this before you start driving to ensure your safety.

Step 2: Working With the Ignition Key

In this case, you have to get the ignition key first. Then, after you get the key, you have to check the ignition lock and put the key inside it.

After putting the key inside, you have to move it and get back to position zero. If you want, you can also keep it in position 1.

Step 3: Pushing Set/Reset Button

After selecting position zero or one, you are now ready to go to the next step. In this step, you have to manage the SEL/RESET knob.

You have to do is push it. But please don’t leave it. You have to keep it there. If you do not get the Sel/Reset button, you can check the instrument panel.

You will see the button beside the fuel gauge. If your car doesn’t include the button there, you can check below another button called Multi-Information Display Info.

You will spot it on the right side of the steering wheel. Search for it, push it, and hold it there!

Step 4: Turning the Headlight ON

After you have searched and found the Sel/Reset button and hold it for a few seconds, now it is time to get your hands on the headlights again. This time, you have to turn on the headlights.

Step 5: Turning the Ignition Switch ON

Once doing everything with the headlights, now you have to go ahead and start to work with the ignitions switch.

In this step, you have to turn on the ignition switch carefully.

Note: After turning on the headlights and the ignition switch, get ready for some extra lights.

If you see some extra light coming on, that means that it is working perfectly. In this circumstance, you have to be serious about your security.

And so, you must wear a seatbelt. If you, however, forget to wear a seatbelt, the car will give you a warning sound. When you hear the sound, you have to wear it if you are not wearing it.

Step 6: Continuous OFF and ON Process

If you see the lights coming on, you have to get ready for this step. But, first, you have to make sure that you are fast enough in this step.

You have to do your job of switching the headlights off and then turning them on, and that is within just five seconds.

Make sure that you are already holding the Sel/Reset button. Keeping the button on hold, you have to get your hands on the headlights.

And then, all you need to do is turn the headlight first and then turn it off. After this, you have to turn it off again. We told you earlier that you need to get ready for this process!

Step 7: Releasing The Button

After turning off and off the headlights, you have to get to the Sel/Reset button again quickly.

This time you don’t need to hold it anymore. Release the button. For this, you will get five seconds only. So make sure you complete the work within the time.

Step 8: Keep Repeating

In the process of how to reset the GM instrument Cluster, the step of repeating is normal.

In this step, you have to repeat doing the same work, but this time, you do not have to do with the headlights, but the Sel/Reset button!

It would be helpful if you pushed the Sel/Reset button before. And now, you have to release the button. Then you have to continue pushing the button and then releasing it. So you have to do this three times in a row.

With every press on the Sel/Reset button, there will be new cycling of the gauges. In this process, it will begin another cycling that contains all the gauges.

And we are almost done with the process of resetting it. In this situation, you will see that the instrument cluster will start self-testing!

Step 9: Ending it

So, now the job of resetting the GM Instrument cluster. Now, it is time to end it. So, please go through the ignition switch and switch it off.

There is another way of turning it off. You have to start the vehicle and take a speed of more than 1.5 mph. As a result, it will end automatically.

Step 10: Reinstalling Headlights Fuses

After resetting everything; now, you have to reinstall the headlight fuses. Do you recognize the 15A headlight fuses?

Yes, now you have to reinstall them. Take them to the underhood fuse box and reinstall them.


If you are a GM owner, you know how it feels not to get the current information when you are driving. And to sort it out, all you have to do is reset the GM instrument cluster!

In this article, we have written a process of resetting the GM instrument cluster. This is a quick method, and it can help you search for how to reset the GM instrument cluster. Also, comment below on how you reset it!

-our editorial board has reviewed this article and has been approved for publication according to our editorial policy.

Automotive products are like an addiction to me. Years ago, I started my job at a Roof Box installation co. Then I realized that I have a passion for cars. It is a perfect scope to share my different experiences about automotive products.

Leave a Comment